Download Free Identification Of Low Order Equivalent System Models From Flight Test Data Book in PDF and EPUB Free Download. You can read online Identification Of Low Order Equivalent System Models From Flight Test Data and write the review.

Identification of low order equivalent system dynamic models from flight test data was studied. Inputs were pilot control deflections, and outputs were aircraft responses, so the models characterized the total aircraft response including bare airframe and flight control system. Theoretical investigations were conducted and related to results found in the literature. Low order equivalent system modeling techniques using output error and equation error parameter estimation in the frequency domain were developed and validated on simulation data. It was found that some common difficulties encountered in identifying closed loop low order equivalent system models from flight test data could be overcome using the developed techniques. Implications for data requirements and experiment design were discussed. The developed methods were demonstrated using realistic simulation cases, then applied to closed loop flight test data from the NASA F-18 High Alpha Research Vehicle.Morelli, Eugene A.Langley Research CenterEXPERIMENT DESIGN; DYNAMIC MODELS; SYSTEM IDENTIFICATION; FLIGHT TESTS; DATA PROCESSING; FLIGHT CONTROL; DEFLECTION; AIRCRAFT PERFORMANCE; ERROR ANALYSIS; FLIGHT CHARACTERISTICS; FEEDBACK CONTROL
Downscaled physical models, also referred to as subscale models, have played an essential role in the investigation of the complex physics of flight until the recent disruption of numerical simulation. Despite the fact that improvements in computational methods are slowly pushing experimental techniques towards a secondary role as verification or calibration tools, real-world testing of physical prototypes still provides an unmatched confidence. Physical models are very effective at revealing issues that are sometimes not correctly identified in the virtual domain, and hence can be a valuable complement to other design tools. But traditional wind-tunnel testing cannot always meet all of the requirements of modern aeronautical research and development. It is nowadays too expensive to use these scarce facilities to explore different design iterations during the initial stages of aircraft development, or to experiment with new and immature technologies. Testing of free-flight subscale models, referred to as Subscale Flight Testing (SFT), could offer an affordable and low-risk alternative for complementing conventional techniques with both qualitative and quantitative information. The miniaturisation of mechatronic systems, the advances in rapid-prototyping techniques and power storage, as well as new manufacturing methods, currently enable the development of sophisticated test objects at scales that were impractical some decades ago. Moreover, the recent boom in the commercial drone industry has driven a quick development of specialised electronics and sensors, which offer nowadays surprising capabilities at competitive prices. These recent technological disruptions have significantly altered the cost-benefit function of SFT and it is necessary to re-evaluate its potential in the contemporary aircraft development context. This thesis aims to increase the comprehension and knowledge of the SFT method in order to define a practical framework for its use in aircraft design; focusing on low-cost, short-time solutions that don’t require more than a small organization and few resources. This objective is approached from a theoretical point of view by means of an analysis of the physical and practical limitations of the scaling laws; and from an empirical point of view by means of field experiments aimed at identifying practical needs for equipment, methods, and tools. A low-cost data acquisition system is developed and tested; a novel method for semi-automated flight testing in small airspaces is proposed; a set of tools for analysis and visualisation of flight data is presented; and it is also demonstrated that it is possible to explore and demonstrate new technology using SFT with a very limited amount of economic and human resources. All these, together with a theoretical review and contextualisation, contribute to increasing the comprehension and knowledge of the SFT method in general, and its potential applications in aircraft conceptual design in particular.
This book and its companion volume, LNCS vols. 7331 and 7332, constitute the Proceedings of the Third International conference on Swarm Intelligence, ICSI 2012, held in Shenzhen, China in June 2012. The 145 full papers presented were carefully reviewed and selected from 247 submissions. The papers are organized in 27 cohesive sections covering all major topics of swarm intelligence research and developments.
Lists citations with abstracts for aerospace related reports obtained from world wide sources and announces documents that have recently been entered into the NASA Scientific and Technical Information Database.
The importance of recognizing that each lower-order model used for rotorcraft parameter identification has a limited range of applicability is illustrated in some detail. Examples are given to illustrate the use of conditioning the test input signals and the potential of using multi-axis test inputs to enhance the parameter identifiability. The paper discusses the benefits and limitations of using frequency sweeps as flight-test input signals for identification of frequency response for rotorcraft and for the subsequent fitting of parametric transfer-function models. This paper demonstrates the major role played by analytical modeling and the understanding of the physics involved in the rotorcraft flight dynamics, particularly understanding the limit of lower-order models, in achieving successful rotorcraft parameter identification. (Author).