Download Free Braking Stability And Control Performance Test Procedures For Air And Hydraulic Brake Equipped Trucks Truck Tractors And Buses Book in PDF and EPUB Free Download. You can read online Braking Stability And Control Performance Test Procedures For Air And Hydraulic Brake Equipped Trucks Truck Tractors And Buses and write the review.

This SAE Recommended Practice provides a road test procedure for trucks, truck-tractors, and buses to evaluate their compliance with Federal Motor Vehicle Safety Standards (FMVSS) 105 and 121; Hydraulic and Air Brake Systems. Units of measure are English in lieu of metric to be commensurate with FMVSS 105 and 121. This document is being Stabilized because it covers technology, products, or processes which are mature and could be used for past legacy and/or historical tests.
This Recommended Practice provides a road test procedure for trucks and buses, to evaluate their compliance with Federal Motor Vehicle Safety Standard (FMVSS) 121; Air Brake Systems. Units of measure are English in lieu of metric to be consistent with FMVSS 121. This SAE Recommended Practice is intended as a guide toward industry practice and subject to change so as to keep pace with experience and technical advances. The usage of this recommend practice is limited to trucks and buses equipped with air brake systems with a GVWR greater than 10000 pounds.This document has been modified from SAE J1626-1 truck tractor to incorporate air brake equipped trucks and buses test procedure. The following sections were modified; changed all truck tractor wording to trucks and buses throughout the document, 3.1 definitions add trucks and buses, 3.5 was removed based on combination weight not applicable, 3.7.1 was removed based on tractor trailer combination not applicable and modified for trucks and buses, 3.13 remove unbraked control trailer not applicable, 6.8 removed control trailer reservoir not applicable, 6.13 and 8.2.2 removed the additional brake adjustment at the completion of the 500 snub burnish not applicable with trucks and buses, Section 7 test sequence was modified to follow FMVSS 121 truck and bus sequence, 8.1.3 truck and bus loading changes, 9.1.3, 10.1.2 and 11.1.2 removed brake adjustments not applicable, 9.1.1 corrected 20 foot cone spacing, 9.2.1 changed 35 to 30 mph and changed 44 to 40 mph, 9.2.2 corrected reference 3.9 to 3.8, 11.2.1a removed the word "only," Figure 5D removed LLVW, and corrected all header spacing between two-digit section number and header. Figures (data sheets) removed trailer ballast C.G. height measurement, bobtail proportional and fifth wheel height not applicable. SAE J1626-2 has been reaffirmed to comply with the SAE Five-Year Review policy.
This Recommended Practice provides a road test procedure for truck-tractors, to evaluate their compliance with Federal Motor Vehicle Safety Standard (FMVSS) 121; Air Brake Systems. Units of measure are English in lieu of metric to be consistent with FMVSS 121. This series of SAE Recommended Practices have been developed by the Truck and Bus Vehicle Deceleration and Stability Subcommittee combined with the Brake Systems Subcommittee sponsored by the Brake Committee. These SAE Recommended Practices are intended as a guide toward industry practice and are subject to change so as to keep pace with experience and technical advances. The usage of these recommended practices are limited to vehicles equipped with air brake systems and hydraulic brake vehicles with a GVWR greater than 10 000 lb.The current SAE J1626 included air and hydraulic type brake vehicle test procedures combined in one document. With the complexity of this document as combined, it was determined to better serve our industry that the subcommittee should rewrite this document into separate procedures.As described in the parent document, SAE J1626, there are a minimum of five documents required for air- and hydraulic-braked vehicles noted below in the References Section. This procedure addresses the truck-tractor air brake combination vehicle. In summary, the following changes were addressed; aScope - separated this document into the truck-tractor procedure bReferences - added the new separate procedure numbers and included other new references as appropriate including SAE J360 (Truck and Bus Grade Parking Performance Test Procedure) and SAE J1729 (Parking Brake Drawbar Pull Test Procedure. cTest Conditions - snub burnish conditioning procedure will be conducted with the transmission in gear. This was a procedure change. Included brake adjustment clarification and recommended intervals. dTest Sequence - this was revised to follow FMVSS 121 truck-tractor test sequence. eTest Procedures - included maximum braking speed test to the stability and controls test. An optional test was added to initiate additional stops at a fully exhausted reservoir pressure at or near 0 psi during the failed system reservoir stops. fData Sheets - added the procedure changes and updates as appropriate for clarification.
This SAE Recommended Practice provides a test procedure for trucks to evaluate their compliance with Federal Motor Vehicle Safety Standard (FMVSS) 121; Air Brake Systems. Units of measure are English in lieu of metric to be commensurate with FMVSS 121.
Test procedure for Anti-Lock brake system (ABS/Anti-Lock) performance for on-highway commercial vehicles over 4536 kg (10 000 lb). This test procedure is intended to determine vehicle stability, maneuverability, stopping capability and system function on various road surface conditions including variable and uniform friction surfaces while brakes are modulated to obtain maximum performance with activation of ABS/Anti-Lock. This procedure does not cover radio frequency interference or power consumption testing. Reference SAE J46 Wheel-Slip Brake Control Road Test Code for passenger car and light truck test procedure.