Download Free Water Injection In The Modern Automotive Spark Ignition Engine Book in PDF and EPUB Free Download. You can read online Water Injection In The Modern Automotive Spark Ignition Engine and write the review.

"The injection of water in the spark ignition engine is not new. The effect of humidity in the air on the performance of the spark ignition engine probably initiated the early investigations. The water vapor in the inlet air decreases the speed of the flame front and necessitates spark advance to assure maximum power and maximum efficiency. Water particles in the air evaporate during the compression and combustion of the inducted charge and decrease the tendency of the engine to detonate. These effects are very evident when operating the spark ignition engine in a moist atmosphere. Water is not a foreign element to the internal combustion engine. It can be easily shown that when one pound of a hydrocarbon fuel burns more than one pound of water is formed in the combustion chamber ... The fundamental reason for injecting water is to suppress detonation. The exact nature as to how this is accomplished is not definitely known, but it is reasoned that the effect is due to the high heat of vaporization of the water"--Introduction, leaves 1-2.
Water injection is one of the most promising technologies to improve the engine combustion efficiency, by mitigating knock occurrences and controlling exhaust gas temperature before turbine. As result, the engine can operate at stoichiometric conditions over the whole engine map, even during the more power-demanding RDE cycles. Antonino Vacca presents a methodology to study and optimize the effect of water injection for gasoline engines by investigating different engine layouts and injection strategies through the set-up of a 3D-CFD virtual test bench. He investigates indirect and direct water injection strategies to increase the engine knock limit and to reduce exhaust gas temperature for several operating points.
Summary: An investigation has been made of the effectiveness of water injection into the combustion end zone of a spark-ignition engine cylinder for the suppression of knock. Pressure-time recoreds obtained show that injection of water at 60° B.T.C. on the compression stroke at a water-fuel ratio of 0.3 rendered M-3 fuel as good as S-3 fuel from an antiknock consideration. The optimum crank angle for injection of water into the end zone was found to be critical. As the injection angle was increased beyond the optimum, the quantity of water required to suppress knock increased to 3.6 water-fuel ratio at 132° B.T.C. The water quantity could not be increased beyond 3.6 water-fuel ration because of injection-pump limitations; however, a further increase in the injection angle up to the earliest angle obtainable, which was 20° A.T.C. on the intake stroke, continuously increased the knock intensity. The engine operating conditions of the tests did not simulate those encountered in flight, especially with regard to the operating speed of 570 rpm. For this reason the results should only be regarded as of theoretical importance until further investigation has been made.
This book focuses on the investigation of innovative engine technologies that can improve the efficiency of internal combustion engines and reduce their environmental impact. In particular, water injection is examined as a means of improving engine behavior. The possible combination of water injection with renewable fuels is also a topic of the book. The results of this experimental and numerical research show positive results that can be used for further research and development of engines. Content 3D-CFD Simulation Environment: the Virtual Engine Test Bench Experimental Spray Analysis and 3D-CFD Injection Model Calibration Applicability of Water Injection in Combination with an eFuel Water-in-Fuel Emulsions at the Virtual Engine Test Bench Target Groups Students and researchers in the field of automotive engineering, esp. engine technology Engineers in the automotive industry About the Author Edoardo Rossi is a project manager in the virtual engine development department at the FKFS, where he did his PhD. He works on innovative solutions for future powertrain technologies for motor vehicles. .
Homogeneous charge compression ignition (HCCI)/controlled auto-ignition (CAI) has emerged as one of the most promising engine technologies with the potential to combine fuel efficiency and improved emissions performance, offering reduced nitrous oxides and particulate matter alongside efficiency comparable with modern diesel engines. Despite the considerable advantages, its operational range is rather limited and controlling the combustion (timing of ignition and rate of energy release) is still an area of on-going research. Commercial applications are, however, close to reality. HCCI a.
Abstract : An experimental effort has been completed in which water injection was investigated as a means of enabling increases in engine output and high load efficiency. Water was injected into the intake port of a direct fuel injected, 4-cylinder, boosted engine with dual independent variable valve timing. The water was shown to increase volumetric efficiency and decrease the onset of knock which in turn enable more optimal combustion phasing. Both of these affects resulted increases in load of up to 5.5% at the same manifold pressure as the baseline case. The advancement of combustion phasing, combined with elimination of fuel enrichment resulted in an increase in full load thermal efficiency of up to 35%. Analysis is provided around these affects, as well as the phase transformation of water throughout the engine cycle.
Fuel injection systems and performance is fundamental to combustion engine performance in terms of power, noise, efficiency, and exhaust emissions. There is a move toward electric vehicles (EVs) to reduce carbon emissions, but this is unlikely to be a rapid transition, in part due to EV batteries: their size, cost, longevity, and charging capabilities as well as the scarcity of materials to produce them. Until these isssues are resolved, refining the spark-ignited engine is necessary address both sustainability and demand for affordable and reliable mobility. Even under policies oriented to smart sustainable mobility, spark-ignited engines remain strategic, because they can be applied to hybridized EVs or can be fueled with gasoline blended with bioethanol or bio-butanol to drastically reduce particulate matter emissions of direct injection engines in addition to lower CO2 emissions. In this book, Alessandro Ferrari and Pietro Pizzo provide a full review of spark-ignited engine fuel injection systems. The most popular typologies of fuel injection systems are considered, with special focus on state-of-the-art solutions. Dedicated sections on the methods for air mass evaluation, fuel delivery low-pressure modules, and the specific subsystems for idle, cold start, and warm-up control are also included. The authors pay special attention to mixture formation strategies, as they are a fundamental theme for SI engines. An exhaustive overview of fuel injection technologies is provided, and mixture formation strategies for spark ignited combustion engines are considered. Fuel Injection Systems illustrates the performance of these systems and will also serve as a reference for engineers who are active in the aftermarket, offering detailed information on fuel injection system solutions that are mounted in older vehicles.