Download Free Ultimate Strength Of Prestressed Concrete Beams In Combined Bending And Torsion Book in PDF and EPUB Free Download. You can read online Ultimate Strength Of Prestressed Concrete Beams In Combined Bending And Torsion and write the review.

This highly successful textbook has been comprehensively revised for two main reasons: to bring the book up-to-date and make it compatible with BS8110 1985; and to take into account the increasing use made of microcomputers in civil engineering. An important new chapter on microcomputer applications has been added.
Prestressing concrete technology is critical to understanding problems in existing civic structures including railway and highway bridges; to the rehabilitation of older structures; and to the design of new high-speed railway and long-span highway bridges. Analysis and Design of Prestressed Concrete delivers foundational concepts, and the latest research and design methods for the engineering of prestressed concrete, paying particular attention to crack resistance in the design of high-speed railway and long-span highway prestressed concrete bridges. The volume offers readers a comprehensive resource on prestressing technology and applications, as well as the advanced treatment of prestress losses and performance. Key aspects of this volume include analysis and design of prestressed concrete structures using a prestressing knowledge system, from initial stages to service; detailed loss calculation; time-dependent analysis on cross-sectional stresses; straightforward, simplified methods specified in codes; and in-depth calculation methods. Sixteen chapters combine standards and current research, theoretical analysis, and design methods into a practical resource on the analysis and design of prestressed concrete, as well as presenting novel calculation methods and theoretical models of practical use to engineers. - Presents a new approach to calculating prestress losses due to anchorage seating - Provides a unified method for calculating long-term prestress loss - Details cross-sectional stress analysis of prestressed concrete beams from jacking to service - Explains a new calculation method for long-term deflection of beams caused by creep and shrinkage - Gives a new theoretical model for calculating long-term crack width
Proceedings of the symposium cosponsored by the American Concrete lnstitute, the Comité Euro­ International du Béton, the Prestressed Concrete lnstitute, and the Fédération Internationale de la Précontrainte.
Ultra High Performance Concrete (UHPC) is characterized by a very high compressive strength which may reach more than 200 MPa. The behavior of this material under tension and compression actions has been established to be very brittle in nature. Discontinuous fibers (normally steel fibers) are usually added to the UHPC mix to introduce ductility. In order to investigate the beneficial effects of using fiber reinforced UHPC in structural members subjected to torsion, a series of experimental tests on 17 UHPC beams subjected to pure torsion were carried out. The test beams consisted of plain UHPC beams, UHPC beams reinforced with steel fibers only, UHPC reinforced with steel fibers and different combinations of traditional longitudinal and transverse reinforcement. The plain UHPC beams showed very brittle behavior, whereas the UHPC beams with steel fibers only showed a post cracking ductile behavior. The addition of little steel fiber volume (e.g. 0.5 %) to the plain UHPC beams enhanced the ductility. The enhancement at the ultimate capacity amounts to about 20 %. Meanwhile, the steel fibers with 0.9 % by volume showed much enhanced ductility and a maximum enhancement of the torsional carrying capacity up to 32 %. The addition of moderate steel fiber volume (e.g. 0.9 %) to one type of traditional reinforcement (either longitudinal or transverse) accomplished an effective post cracking torsional carrying mechanism. The steel fibers shows a tendency to replace the missing type of traditional reinforcement, however this should be confirmed by more tests and by using higher steel fiber volumes. A series of experimental tests on fiber reinforced UHPC prisms to investigate the post cracking shear strength and stiffness of the used UHPC mix (e.g. M3Q) was conducted. The results of these tests revealed that this fine grained UHPC mix has a weak post cracking shear behavior. The results of these tests were used later in the Finite Element (F.E) model. An analytical model based on the well known thin-walled tube analogy was developed in order to estimate the torsional carrying capacity of beams under pure torsion having different combinations of steel fibers and traditional reinforcement. The comparison between the test and model results showed very good agreement for all cases. A finite element model based on calibrated small scale tests was developed using ATENA F.E. package to predict the full load-deformation behavior of the test beams. The predictions of the model show very good agreement with the test results.
This Proceedings contains the papers of the fib Symposium “CONCRETE Innovations in Materials, Design and Structures”, which was held in May 2019 in Kraków, Poland. This annual symposium was co-organised by the Cracow University of Technology. The topics covered include Analysis and Design, Sustainability, Durability, Structures, Materials, and Prefabrication. The fib, Fédération internationale du béton, is a not-for-profit association formed by 45 national member groups and approximately 1000 corporate and individual members. The fib’s mission is to develop at an international level the study of scientific and practical matters capable of advancing the technical, economic, aesthetic and environmental performance of concrete construction. The fib, was formed in 1998 by the merger of the Euro-International Committee for Concrete (the CEB) and the International Federation for Prestressing (the FIP). These predecessor organizations existed independently since 1953 and 1952, respectively.
This book on Reinforced Concrete has been comprehensively revised with a view to make it more suitable for the updated syllabus of various Technical Institutes and Engineering Colleges of different Universities.