Download Free Switch Level Fault Simulation Of Mos Vlsi Circuits Book in PDF and EPUB Free Download. You can read online Switch Level Fault Simulation Of Mos Vlsi Circuits and write the review.

Only two decades ago most electronic circuits were designed with a slide-rule, and the designs were verified using breadboard techniques. Simulation tools were a research curiosity and in general were mistrusted by most designers and test engineers. In those days the programs were not user friendly, models were inadequate, and the algorithms were not very robust. The demand for simulation tools has been driven by the increasing complexity of integrated circuits and systems, and it has been aided by the rapid decrease in the cost of com puting that has occurred over the past several decades. Today a wide range of tools exist for analYSiS, deSign, and verification, and expert systems and synthesis tools are rapidly emerging. In this book only one aspect of the analysis and design process is examined. but it is a very important aspect that has received much attention over the years. It is the problem of accurate circuit and timing simulation.
Power supply current monitoring to detect CMOS IC defects during production testing quietly laid down its roots in the mid-1970s. Both Sandia Labs and RCA in the United States and Philips Labs in the Netherlands practiced this procedure on their CMOS ICs. At that time, this practice stemmed simply from an intuitive sense that CMOS ICs showing abnormal quiescent power supply current (IDDQ) contained defects. Later, this intuition was supported by data and analysis in the 1980s by Levi (RACD, Malaiya and Su (SUNY-Binghamton), Soden and Hawkins (Sandia Labs and the University of New Mexico), Jacomino and co-workers (Laboratoire d'Automatique de Grenoble), and Maly and co-workers (Carnegie Mellon University). Interest in IDDQ testing has advanced beyond the data reported in the 1980s and is now focused on applications and evaluations involving larger volumes of ICs that improve quality beyond what can be achieved by previous conventional means. In the conventional style of testing one attempts to propagate the logic states of the suspended nodes to primary outputs. This is done for all or most nodes of the circuit. For sequential circuits, in particular, the complexity of finding suitable tests is very high. In comparison, the IDDQ test does not observe the logic states, but measures the integrated current that leaks through all gates. In other words, it is like measuring a patient's temperature to determine the state of health. Despite perceived advantages, during the years that followed its initial announcements, skepticism about the practicality of IDDQ testing prevailed. The idea, however, provided a great opportunity to researchers. New results on test generation, fault simulation, design for testability, built-in self-test, and diagnosis for this style of testing have since been reported. After a decade of research, we are definitely closer to practice.
VLSI systems are becoming very complex and difficult to test. Traditional stuck-at fault problems may be inadequate to model possible manufacturing defects in the integrated ciruit. Hierarchial models are needed that are easy to use at the transistor and functional levels. Stuck-open faults present severe testing problems in CMOS circuits, to overcome testing problems testable designs are utilized. Bridging faults are important due to the shrinking geometry of ICs. BIST PLA schemes have common features-controllability and observability - which are enhanced through additional logic and test points. Certain circuit topologies are more easily testable than others. The amount of reconvergent fan-out is a critical factor in determining realistic measures for determining test generation difficulty. Test implementation is usually left until after the VLSI data path has been synthesized into a structural description. This leads to investigation methodologies for performing design synthesis with test incorporation. These topics and more are discussed.
VLSI Electronics Microstructure Science, Volume 20: VLSI and Computer Architecture reviews the approaches in design principles and techniques and the architecture for computer systems implemented in VLSI. This volume is divided into two parts. The first section is concerned with system design. Chapters under this section focus on the discussion of such topics as the evolution of VLSI; system performance and processor design considerations; and VLSI system design and processing tools. Part II of the book focuses on the architectural possibilities that have become cost effective with the development of VLSI circuits. Topics on architectural requirements and various architectures such as the Reduced Instruction Set, Extended Von Neumann, Language-Oriented, and Microprogrammable architectures are elaborated in detail. Also included are chapters that discuss the evaluation of architecture, multiprocessing configurations, and the future of VLSI. Computer designers, those evaluating computer systems, researchers, and students of computer architecture will find the book very useful.
This description of the structure of simulators suitable for use in the design of digital electronic systems includes the compiled code and event driven algorithms for digital electronic system simulators, together with timing verification as well as structural limitations and problems.
The summer school on VLSf GAD Tools and Applications was held from July 21 through August 1, 1986 at Beatenberg in the beautiful Bernese Oberland in Switzerland. The meeting was given under the auspices of IFIP WG 10. 6 VLSI, and it was sponsored by the Swiss Federal Institute of Technology Zurich, Switzerland. Eighty-one professionals were invited to participate in the summer school, including 18 lecturers. The 81 participants came from the following countries: Australia (1), Denmark (1), Federal Republic of Germany (12), France (3), Italy (4), Norway (1), South Korea (1), Sweden (5), United Kingdom (1), United States of America (13), and Switzerland (39). Our goal in the planning for the summer school was to introduce the audience into the realities of CAD tools and their applications to VLSI design. This book contains articles by all 18 invited speakers that lectured at the summer school. The reader should realize that it was not intended to publish a textbook. However, the chapters in this book are more or less self-contained treatments of the particular subjects. Chapters 1 and 2 give a broad introduction to VLSI Design. Simulation tools and their algorithmic foundations are treated in Chapters 3 to 5 and 17. Chapters 6 to 9 provide an excellent treatment of modern layout tools. The use of CAD tools and trends in the design of 32-bit microprocessors are the topics of Chapters 10 through 16. Important aspects in VLSI testing and testing strategies are given in Chapters 18 and 19.
An easy to use introduction to the practices and techniques in the field of digital circuit testing. Lala writes in a user-friendly and tutorial style, making the book easy to read, even for the newcomer to fault-tolerant system design. Each informative chapter is self-contained, with little or no previous knowledge of a topic assumed. Extensive references follow each chapter.