Download Free Noise Coupling In System On Chip Book in PDF and EPUB Free Download. You can read online Noise Coupling In System On Chip and write the review.

Noise Coupling is the root-cause of the majority of Systems on Chip (SoC) product fails. The book discusses a breakthrough substrate coupling analysis flow and modelling toolset, addressing the needs of the design community. The flow provides capability to analyze noise components, propagating through the substrate, the parasitic interconnects and the package. Using this book, the reader can analyze and avoid complex noise coupling that degrades RF and mixed signal design performance, while reducing the need for conservative design practices. With chapters written by leading international experts in the field, novel methodologies are provided to identify noise coupling in silicon. It additionally features case studies that can be found in any modern CMOS SoC product for mobile communications, automotive applications and readout front ends.
The book reports modeling and simulation techniques for substrate noise coupling effects in RFICs and introduces isolation structures and design guides to mitigate such effects with the ultimate goal of enhancing the yield of RF and mixed signal SoCs. The book further reports silicon measurements, and new test and noise isolation structures. To the authors’ knowledge, this is the first title devoted to the topic of substrate noise coupling in RFICs as part of a large SoC.
This book is the first in a series of three dedicated to advanced topics in Mixed-Signal IC design methodologies. It is one of the results achieved by the Mixed-Signal Design Cluster, an initiative launched in 1998 as part of the TARDIS project, funded by the European Commission within the ESPRIT-IV Framework. This initiative aims to promote the development of new design and test methodologies for Mixed-Signal ICs, and to accelerate their adoption by industrial users. As Microelectronics evolves, Mixed-Signal techniques are gaining a significant importance due to the wide spread of applications where an analog front-end is needed to drive a complex digital-processing subsystem. In this sense, Analog and Mixed-Signal circuits are recognized as a bottleneck for the market acceptance of Systems-On-Chip, because of the inherent difficulties involved in the design and test of these circuits. Specially, problems arising from the use of a common substrate for analog and digital components are a main limiting factor. The Mixed-Signal Cluster has been formed by a group of 11 Research and Development projects, plus a specific action to promote the dissemination of design methodologies, techniques, and supporting tools developed within the Cluster projects. The whole action, ending in July 2002, has been assigned an overall budget of more than 8 million EURO.
Presenting a comprehensive overview of the design automation algorithms, tools, and methodologies used to design integrated circuits, the Electronic Design Automation for Integrated Circuits Handbook is available in two volumes. The second volume, EDA for IC Implementation, Circuit Design, and Process Technology, thoroughly examines real-time logic to GDSII (a file format used to transfer data of semiconductor physical layout), analog/mixed signal design, physical verification, and technology CAD (TCAD). Chapters contributed by leading experts authoritatively discuss design for manufacturability at the nanoscale, power supply network design and analysis, design modeling, and much more. Save on the complete set.
The second of two volumes in the Electronic Design Automation for Integrated Circuits Handbook, Second Edition, Electronic Design Automation for IC Implementation, Circuit Design, and Process Technology thoroughly examines real-time logic (RTL) to GDSII (a file format used to transfer data of semiconductor physical layout) design flow, analog/mixed signal design, physical verification, and technology computer-aided design (TCAD). Chapters contributed by leading experts authoritatively discuss design for manufacturability (DFM) at the nanoscale, power supply network design and analysis, design modeling, and much more. New to This Edition: Major updates appearing in the initial phases of the design flow, where the level of abstraction keeps rising to support more functionality with lower non-recurring engineering (NRE) costs Significant revisions reflected in the final phases of the design flow, where the complexity due to smaller and smaller geometries is compounded by the slow progress of shorter wavelength lithography New coverage of cutting-edge applications and approaches realized in the decade since publication of the previous edition—these are illustrated by new chapters on 3D circuit integration and clock design Offering improved depth and modernity, Electronic Design Automation for IC Implementation, Circuit Design, and Process Technology provides a valuable, state-of-the-art reference for electronic design automation (EDA) students, researchers, and professionals.
Physical Design for 3D Integrated Circuits reveals how to effectively and optimally design 3D integrated circuits (ICs). It also analyzes the design tools for 3D circuits while exploiting the benefits of 3D technology. The book begins by offering an overview of physical design challenges with respect to conventional 2D circuits, and then each chapter delivers an in-depth look at a specific physical design topic. This comprehensive reference: Contains extensive coverage of the physical design of 2.5D/3D ICs and monolithic 3D ICs Supplies state-of-the-art solutions for challenges unique to 3D circuit design Features contributions from renowned experts in their respective fields Physical Design for 3D Integrated Circuits provides a single, convenient source of cutting-edge information for those pursuing 2.5D/3D technology.
This book discusses the new roles that the VLSI (very-large-scale integration of semiconductor circuits) is taking for the safe, secure, and dependable design and operation of electronic systems. The book consists of three parts. Part I, as a general introduction to this vital topic, describes how electronic systems are designed and tested with particular emphasis on dependability engineering, where the simultaneous assessment of the detrimental outcome of failures and cost of their containment is made. This section also describes the related research project “Dependable VLSI Systems,” in which the editor and authors of the book were involved for 8 years. Part II addresses various threats to the dependability of VLSIs as key systems components, including time-dependent degradations, variations in device characteristics, ionizing radiation, electromagnetic interference, design errors, and tampering, with discussion of technologies to counter those threats. Part III elaborates on the design and test technologies for dependability in such applications as control of robots and vehicles, data processing, and storage in a cloud environment and heterogeneous wireless telecommunications. This book is intended to be used as a reference for engineers who work on the design and testing of VLSI systems with particular attention to dependability. It can be used as a textbook in graduate courses as well. Readers interested in dependable systems from social and industrial–economic perspectives will also benefit from the discussions in this book.
The proposal of doubling the number of transistors on an IC chip (with minimum costs and subtle innovations) every 24 months by Gordon Moore in 1965 (the so-called called Moore's law) has been the most powerful driver for the emphasis of the microelectronics industry in the past 50 years. This law enhances lithography scaling and integration, in 2D, of all functions on a single chip, increasingly through system-on-chip (SOC). On the other hand, the integration of all these functions can be achieved through 3D integrations . Generally speaking, 3D integration consists of 3D IC packaging, 3D IC integration, and 3D Si integration. They are different and mostly the TSV (through-silicon via) separates 3D IC packaging from 3D IC/Si integrations since the latter two uses TSVs, but 3D IC packaging does not. TSV (with a new concept that every chip or interposer could have two surfaces with circuits) is the heart of 3D IC/Si integrations. Continued technology scaling together with the integration of disparate technologies in a single chip means that device performance continues to outstrip interconnect and packaging capabilities, and hence there exist many difficult engineering challenges, most notably in power management, noise isolation, and intra and inter-chip communication. 3D Si integration is the right way to go and compete with Moore's law (more than Moore versus more Moore). However, it is still a long way to go. In this book, Fengyuan SUN proposes new substrate network extraction techniques. Using this latter, the substrate coupling and loss in IC's can be analyzed. He implements some Green/TLM (Transmission Line Matrix) algorithms in MATLAB. It permits to extract impedances between any number of embedded contacts or/and TSVS. He does investigate models of high aspect ratio TSV, on both analytical and numerical methods electromagnetic simulations. This model enables to extract substrate and TSV impedance, S parameters and parasitic elements, considering the variable resistivity of the substrate. It is full compatible with SPICE-like solvers and should allow an investigation in depth of TSV impact on circuit performance.
Modern microelectronic design is characterized by the integration of full systems on a single die. These systems often include large high performance digital circuitry, high resolution analog parts, high driving I/O, and maybe RF sections. Designers of such systems are constantly faced with the challenge to achieve compatibility in electrical characteristics of every section: some circuitry presents fast transients and large consumption spikes, whereas others require quiet environments to achieve resolutions well beyond millivolts. Coupling between those sections is usually unavoidable, since the entire system shares the same silicon substrate bulk and the same package. Understanding the way coupling is produced, and knowing methods to isolate coupled circuitry, and how to apply every method, is then mandatory knowledge for every IC designer. Analysis and Solutions for Switching Noise Coupling in Mixed-Signal ICs is an in-depth look at coupling through the common silicon substrate, and noise at the power supply lines. It explains the elementary knowledge needed to understand these phenomena and presents a review of previous works and new research results. The aim is to provide an understanding of the reasons for these particular ways of coupling, review and suggest solutions to noise coupling, and provide criteria to apply noise reduction. Analysis and Solutions for Switching Noise Coupling in Mixed-Signal ICs is an ideal book, both as introductory material to noise-coupling problems in mixed-signal ICs, and for more advanced designers facing this problem.