Download Free Material Characterization And Performance Properties Of Superpave Mixtures Book in PDF and EPUB Free Download. You can read online Material Characterization And Performance Properties Of Superpave Mixtures and write the review.

The primary objectives of this research study was to characterize properties of two NCDOT Superpave mixes with regards to fatigue distress, and to develop phenomenological fatigue relationships for these mixes based on various levels of strain, asphalt content, air void content, and temperatures. Of particular importance was the sensitivity of the Superpave mixes to asphalt content and air void content that are usually expected in-situ. Fatigue characterization of typical pavement sections using NCDOT fatigue models and using mechanistic analysis procedure suggests that the pavement fatigue life is sensitive to the mix variables and test temperatures considered in this study. A decrease in asphalt content by 0.5-percent (by wt. of mix) results in decrease of 18 to 25-percent fatigue life. An increase in 2% air void content will reduce pavement life by about 40% for 12.5-mm mixes, and by almost 60% for 19-mm mixes. An increase in temperature was found to result in decrease in fatigue life of pavement section under consideration, although, fatigue testing was conducted in controlled-strain mode-of-loading. A 5 & deg;C increase in temperature results in about 25-percent reduction in pavement life. Based on the overall result of the analysis, it appears that 19-mm mix is more sensitive to mix and test variables as compared to the 12.5-mm mix. The study of frequency effect on fatigue life of typical pavement section suggests that prediction of fatigue life of pavement section is independent of load frequency used in fatigue test as long as tensile strain is computed based on the same load frequency.
Laboratory fatigue testing was performed on six Superpave HMA mixtures in use at the Virginia Smart Road. Evaluation of the applied strain and resulting fatigue life was performed to fit regressions to predict the fatigue performance of each mixture. Differences in fatigue performance due to field and laboratory production and compaction methods were investigated. Also, in-situ mixtures were compared to mixtures produced accurately from the job mix formula to determine if changes occurring between the laboratory and batch plant significantly affected fatigue life. Results from the fatigue evaluation allowed verification of several hypotheses related to mixture production and compaction and fatigue performance. It was determined that location within the pavement surface, such as inner or outer wheelpath or center-of-lane, did not significantly affect laboratory fatigue test results, although the location will have significant effects on in-situ fatigue life. Also the orientation of samples cut from an in-situ pavement (parallel or perpendicular to the direction of traffic) had only a minor effect on the laboratory fatigue life, because the variability inherent in the pavement due to material variability is greater than the variability induced by compaction. Fatigue life of laboratory-compacted samples was found to be greater than fatigue life of field-compacted samples; additionally, the variability of the laboratory compacted mixture was found to be less than that of the field-compacted samples. However, it was also found that batch-plant production significantly reduces specimen variability as compared to small-batch laboratory production when the same laboratory compaction is used on both specimen sets. Finally, for Smart Road mixtures produced according to the job mix formula, the use of polymer-modified binder or stone matrix asphalt was shown to increase the expected fatigue life. However, results for all mixes indicated that fatigue resistance rankings might change depending on the applied strain level. This study contributes to the understanding of the factors involved in fatigue performance of asphalt mixtures. Considering that approximately 95% of Virginia's interstate and primary roadways incorporate asphalt surface mixtures, and that fatigue is a leading cause of deterioration, gains in the understanding of fatigue processes and prevention have great potential payoff by improving both the mixture and pavement design practices.
"Research sponsored by the American Association of State Highway and Transportation Officials in cooperation with the Federal Highway Administration."
Strategic Highway Research Program (SHRP) A407 recommends that aggregate gradations pass below the restricted zone as traffic level increases. This study investigated the use of natural sand in the fine and coarse gradations for the surface course mixtures. The mixtures were designed using the SUPERPAVE mix design approach and were evaluated for their performance in terms of resistance to rutting, fatigue and moisture damage. In addition, the accelerated performance of these mixtures was also evaluated using the Asphalt Pavement Analyzer.
Thirteen papers presented at the conference on [title], held in Phoenix, Arizona, December, 1994, discuss the products of the strategic highway research program, the Superpave method of mix design, and test methods for fatigue cracking and permanent deformation. Lacks an index. Annotation c. by Book