Download Free Flight Testing And Real Time System Identification Analysis Of A Uh 60a Black Hawk Helicopter With An Instrumented External Sling Load Book in PDF and EPUB Free Download. You can read online Flight Testing And Real Time System Identification Analysis Of A Uh 60a Black Hawk Helicopter With An Instrumented External Sling Load and write the review.

Helicopter slung-load operations are common in both military and civil contexts. Helicopters and loads are often qualified for these operations by means of flight tests, which can be expensive and time consuming. There is significant potential to reduce such costs both through revisions in flight-test methods and by using validated simulation models. To these ends, flight tests were conducted at Moffett Field to demonstrate the identification of key dynamic parameters during flight tests (aircraft stability margins and handling-qualities parameters, and load pendulum stability), and to accumulate a data base for simulation development and validation. The test aircraft was a UH-60A Black Hawk, and the primary test load was an instrumented 8- by 6- by 6-ft cargo container. Tests were focused on the lateral and longitudinal axes, which are the axes most affected by the load pendulum modes in the frequency range of interest for handling qualities; tests were conducted at airspeeds from hover to 80 knots. Using telemetered data, the dynamic parameters were evaluated in near real time after each test airspeed and before clearing the aircraft to the next test point. These computations were completed in under 1 min. A simulation model was implemented by integrating an advanced model of the UH-60A aerodynamics, dynamic equations for the two-body slung-load system, and load static aerodynamics obtained from wind-tunnel measurements. Comparisons with flight data for the helicopter alone and with a slung load showed good overall agreement for all parameters and test points; however, unmodeled secondary dynamic losses around 2 Hz were found in the helicopter model and they resulted in conservative stability margin estimates.
Historically, helicopter and load combinations have been qualified through flight testing, requiring considerable time and cost. With advancements in simulation and flight test techniques, there is potential to substantially reduce costs and increase the safety of helicopter sling load certification. Validated simulation tools make possible accurate prediction of operational flight characteristics before initial flight tests. Real time analysis of test data improves the safety and efficiency of the testing programs. To advance these concepts, the US Army and NASA, in cooperation with the Israeli Air Force and Technion, under a Memorandum of Agreement, seek to develop and validate a numerical model of the UH-60 with sling load and demonstrate a method of near real time flight test analysis. This thesis presents results from flight tests of a US Army Black Hawk helicopter with various external loads. Tests were conducted as the US first phase of this MOA task. The primary load was a container express box (CONEX), which contained a compact instrumentation package. The flights covered the airspeed range from hover to 70 knots. Primary maneuvers were pitch and roll frequency sweeps, steps, and doublets. Results of the test determined the effect of the suspended load on both the aircraft's handling qualities and it's control system's stability margins. Included were calculations of the stability characteristics of the load's pendular motion. Utilizing CIFER software, a method for near-real time system identification was also demonstrated during the flight test program.
Helicopter external air transportation plays an important role in today's world. For both military and civilian helicopters, external sling load operations offer an efficient and expedient method of handling heavy, oversized cargo. With the ability to reach areas otherwise inaccessible by ground transportation, helicopter external load operations are conducted in industries such as logging, construction, and fire fighting, as well as in support of military tactical transport missions. Historically, helicopter and load combinations have been qualified through flight testing, requiring considerable time and cost. With advancements in simulation and flight test techniques there is potential to substantially reduce costs and increase the safety of helicopter sling load certification. Validated simulation tools make possible accurate prediction of operational flight characteristics before initial flight tests. Real time analysis of test data improves the safety and efficiency of the testing programs. To advance these concepts, the U.S. Army and NASA, in cooperation with the Israeli Air Force and Technion, under a Memorandum of Agreement, seek to develop and validate a numerical model of the UH-60 with sling load and demonstrate a method of near real time flight test analysis. This thesis presents results from flight tests of a U.S. Army Black Hawk helicopter with various external loads. Tests were conducted as the U.S. first phase of this MOA task. The primary load was a container express box (CONEX) which contained a compact instrumentation package. The flights covered the airspeed range from hover to 70 knots. Primary maneuvers were pitch and roll frequency sweeps, steps, and doublets. Results of the test determined the effect of the suspended load on both the aircraft's handling qualities and its control system's stability margins. Included were calculations of the stability characteristics of the load's pendular motion. Utilizing CIFER(R) software, a method for near-...
This paper describes a flight test demonstration of a system for identification of the stability and handling qualities parameters of a helicopter-slung load configuration simultaneously with flight testing, and the results obtained.Tests were conducted with a UH-60A Black Hawk at speeds from hover to 80 kts. The principal test load was an instrumented 8 x 6 x 6 ft cargo container. The identification used frequency domain analysis in the frequency range to 2 Hz, and focussed on the longitudinal and lateral control axes since these are the axes most affected by the load pendulum modes in the frequency range of interest for handling qualities. Results were computed for stability margins, handling qualities parameters and load pendulum stability. The computations took an average of 4 minutes before clearing the aircraft to the next test point. Important reductions in handling qualities were computed in some cases, depending, on control axis and load-slung combination. A database, including load dynamics measurements, was accumulated for subsequent simulation development and validation. Cicolani, Luigi S. and McCoy, Allen H. and Tischler, Mark B. and Tucker, George E. and Gatenio, Pinhas and Marmar, Dani Ames Research Center RTOP 581-30-22...
Although many books have been written on the theory of system identification, few are available that provide a complete engineering treatment of system identification and how to successfully apply it to flight vehicles. This book presents proven methods, practical guidelines, and real-world flight-test results for a wide range of state-of-the-art flight vehicles, from small uncrewed aerial vehicles (UAVs) to large manned aircraft/rotorcraft.
July 2019 Printed in BLACK AND WHITE The Army's Weapon Systems Handbook was updated in July 2019, but is still titled "Weapon Systems Handbook 2018." We are printing this in black and white to keep the price low. It presents many of the acquisition programs currently fielded or in development. The U.S. Army Acquisition Corps, with its 36,000 professionals, bears a unique responsibility for the oversight and systems management of the Army's acquisition lifecycle. With responsibility for hundreds of acquisition programs, civilian and military professionals collectively oversee research, development and acquisition activities totaling more than $20 billion in Fiscal Year 2016 alone. Why buy a book you can download for free? We print this so you don't have to. We at 4th Watch Publishing are former government employees, so we know how government employees actually use the standards. When a new standard is released, somebody has to print it, punch holes and put it in a 3-ring binder. While this is not a big deal for a 5 or 10-page document, many DoD documents are over 400 pages and printing a large document is a time- consuming effort. So, a person that's paid $25 an hour is spending hours simply printing out the tools needed to do the job. That's time that could be better spent doing mission. We publish these documents so you can focus on what you are there for. It's much more cost-effective to just order the latest version from Amazon.com. SDVOSB If there is a standard you would like published, let us know. Our web site is usgovpub.com