Download Free Detailed Characterization Of Conventional And Low Temperature Dual Fuel Combustion In Compression Ignition Engines Book in PDF and EPUB Free Download. You can read online Detailed Characterization Of Conventional And Low Temperature Dual Fuel Combustion In Compression Ignition Engines and write the review.

The goal of this study is to assess conventional and low temperature dual fuel combustion in light- and heavy-duty multi-cylinder compression ignition engines in terms of combustion characterization, performance, and emissions. First, a light-duty compression ignition engine is converted to a dual fuel engine and instrumented for in-cylinder pressure measurements. The primary fuels, methane and propane, are each introduced into the system by means of fumigation before the turbocharger, ensuring the air-fuel composition is well-mixed. Experiments are performed at 2.5, 5, 7.5, and 10 bar BMEP at an engine speed of 1800 RPM. Heat release analyses reveal that the ignition delay and subsequent combustion processes are dependent on the primary fuel type and concentration, pilot quantity, and loading condition. At low load, diesel-ignited propane yields longer ignition delay periods than diesel-ignited methane, while at high load the reactivity of propane is more pronounced, leading to shorter ignition delays. At high load (BMEP = 10 bar), the rapid heat release associated with diesel-ignited propane appears to occur even before pilot injection, possibly indicating auto-ignition of the propane-air mixture. Next, a modern, heavy-duty compression ignition engine is commissioned with an open architecture controller and instrumented for in-cylinder pressure measurements. Initial diesel-ignited propane dual fuel experiments (fumigated before the turbocharger) at 1500 RPM reveal that the maximum percent energy substitution (PES) of propane is limited to 86, 60, 33, and 25 percent at 5, 10, 15, and 20 bar BMEP, respectively. Fueling strategy, injection strategy, exhaust gas recirculation (EGR) rate, and intake boost pressure are varied in order to maximize the PES of propane at 10 bar BMEP, which increases from 60 PES to 80 PES of propane. Finally, diesel-ignited propane dual fuel low temperature combustion (LTC) is implemented using early injection timings (50 DBTDC) at 5 bar BMEP. A sweep of injection timings from 10 DBTDC to 50 DBTDC reveals the transition from conventional to low temperature dual fuel combustion, indicated by ultra-low NOx̳ and smoke emissions. Optimization of the dual fuel LTC concept yields less than 0.02 g/kW-hr NOx̳ and 0.06 FSN smoke at 93 PES of propane.
Alternative Fuels and Advanced Vehicle Technologies for Improved Environmental Performance: Towards Zero Carbon Transportation, Second Edition provides a comprehensive view of key developments in advanced fuels and vehicle technologies to improve the energy efficiency and environmental impact of the automotive sector. Sections consider the role of alternative fuels such as electricity, alcohol and hydrogen fuel cells, as well as advanced additives and oils in environmentally sustainable transport. Other topics explored include methods of revising engine and vehicle design to improve environmental performance and fuel economy and developments in electric and hybrid vehicle technologies. This reference will provide professionals, engineers and researchers of alternative fuels with an understanding of the latest clean technologies which will help them to advance the field. Those working in environmental and mechanical engineering will benefit from the detailed analysis of the technologies covered, as will fuel suppliers and energy producers seeking to improve the efficiency, sustainability and accessibility of their work. - Provides a fully updated reference with significant technological advances and developments in the sector - Presents analyses on the latest advances in electronic systems for emissions control, autonomous systems, artificial intelligence and legislative requirements - Includes a strong focus on updated climate change predictions and consequences, helping the reader work towards ambitious 2050 climate change goals for the automotive industry
This book deals with novel advanced engine combustion technologies having potential of high fuel conversion efficiency along with ultralow NOx and particulate matter (PM) emissions. It offers insight into advanced combustion modes for efficient utilization of gasoline like fuels. Fundamentals of various advanced low temperature combustion (LTC) systems such as HCCI, PCCI, PPC and RCCI engines and their fuel quality requirements are also discussed. Detailed performance, combustion and emissions characteristics of futuristic engine technologies such as PPC and RCCI employing conventional as well as alternative fuels are analyzed and discussed. Special emphasis is placed on soot particle number emission characterization, high load limiting constraints, and fuel effects on combustion characteristics in LTC engines. For closed loop combustion control of LTC engines, sensors, actuators and control strategies are also discussed. The book should prove useful to a broad audience, including graduate students, researchers, and professionals Offers novel technologies for improved and efficient utilization of gasoline like fuels; Deals with most advanced and futuristic engine combustion modes such as PPC and RCCI; Comprehensible presentation of the performance, combustion and emissions characteristics of low temperature combustion (LTC) engines; Deals with closed loop combustion control of advanced LTC engines; State-of-the-art technology book that concisely summarizes the recent advancements in LTC technology. .
A detailed second law analysis of dual fuel LTC is not yet available in the open literature even though dual fuel low temperature combustion (LTC) has been studied before. To address this gap, a previously validated, closed-cycle, multi-zone, simulation of diesel-natural gas dual fuel LTC was used to perform a second law analysis. In the current study, a 2.4-liter single-cylinder research engine operating at a nominal load of 6 bar BMEP and 1700 rpm was used. Zone-wise thermodynamic irreversibilities as well as total cumulative entropy generated and lost available work over the closed cycle were quantified. Subsequently, two convenient second-law parameters were defined: (1) the “lost available indicated mean effective pressure” (LAIMEP), which can be interpreted as an engine-size-normalized measure of available work that is lost due to thermodynamic irreversibilities (analogous to the relationship between indicated mean effective pressure and indicated work); (2) fuel conversion irreversibility (FCI), which is defined as the ratio of lost available work to total fuel chemical energy input. Finally, parametric studies were performed to quantify the effects of diesel start of injection, intake manifold temperature, and intake boost pressure on LAIMEP and FCI. The results show that significant entropy generation occurred in the flame zone (52-61 percent) and the burned zone (31-39 percent) while packets account for less than 6 percent of the overall irreversibilities. Parametric studies showed LAIMEPs in the range of 645-768 kPa and FCIs in the range of 32.8-39.2 percent at different engine operating conditions. Although the present study focused on dual fuel LTC, the conceptual definitions of LAIMEP and FCI are generally applicable for comparing the thermodynamic irreversibilities of IC engines of any size and operating on any combustion strategy.
Various combinations of commercially available technologies could greatly reduce fuel consumption in passenger cars, sport-utility vehicles, minivans, and other light-duty vehicles without compromising vehicle performance or safety. Assessment of Technologies for Improving Light Duty Vehicle Fuel Economy estimates the potential fuel savings and costs to consumers of available technology combinations for three types of engines: spark-ignition gasoline, compression-ignition diesel, and hybrid. According to its estimates, adopting the full combination of improved technologies in medium and large cars and pickup trucks with spark-ignition engines could reduce fuel consumption by 29 percent at an additional cost of $2,200 to the consumer. Replacing spark-ignition engines with diesel engines and components would yield fuel savings of about 37 percent at an added cost of approximately $5,900 per vehicle, and replacing spark-ignition engines with hybrid engines and components would reduce fuel consumption by 43 percent at an increase of $6,000 per vehicle. The book focuses on fuel consumption-the amount of fuel consumed in a given driving distance-because energy savings are directly related to the amount of fuel used. In contrast, fuel economy measures how far a vehicle will travel with a gallon of fuel. Because fuel consumption data indicate money saved on fuel purchases and reductions in carbon dioxide emissions, the book finds that vehicle stickers should provide consumers with fuel consumption data in addition to fuel economy information.
This dissertation discusses the results from three different studies aimed at understanding the importance of fuel chemical structure during low temperature combustion (LTC) strategies, like homogeneous charge compression ignition (HCCI) and partially premixed combustion (PPC) employed in internal combustion (IC) engines wherein the focus is on high octane fuels. Boosted intake air operation combined with exhaust gas recirculation, internal as well as external, has become a standard path for expanding the load limits of IC engines employing LTC strategies mentioned above as well as conventional diesel and spark ignition (SI) engines. However, the effects of fuel compositional variation have not been fully explored. The first study focusses on three different fuels, where each of them were evaluated using a single cylinder boosted HCCI engine using negative valve overlap. The three fuels investigated were: a regular grade gasoline (RON = 90.2), 30% ethanol-gasoline blend (E30, RON = 100.3), and 24% iso-butanol-gasoline blend (IB24, RON = 96.6). Detailed sweeps of intake manifold pressure (atmospheric to 250 kPaa), EGR (0 -- 25% EGR), and injection timing were conducted to identify fuel-specific effects. While significant fuel compositional differences existed, the results showed that all these fuels achieved comparable operation with minor changes in operational conditions. Further, it was shown that the available enthalpy from the exhaust would not be sufficient to satisfy the boost requirements at higher load operation by doing an analysis of the required turbocharger efficiency. While the first study concentrated on load expansion of HCCI, it is important to mention that controlling LTC strategies is difficult under low load or idle operating conditions. To ensure stable operation, fuel injection in the negative valve overlap (NVO) is used as one of method of achieving combustion control. However the combustion chemistry under high temperature and fuel rich conditions that exist during the NVO have not been previously explored. The second study focused on examining the products of fuel rich chemistry as a result of fuel injection in the NVO. In this study, a unique six stroke cycle was used to segregate the exhaust from the NVO and to study the chemistry of the range of fuels injected during NVO under low oxygen conditions. The fuels investigated were methanol, ethanol, iso-butanol, and iso-octane. It was observed that the products of reactions under NVO conditions were highly dependent on the injected fuel's structure with iso-octane producing less than 1.5% hydrogen and methanol producing more than 8%. However a weak dependence was observed on NVO duration and initial temperature, indicating that NVO reforming was kinetically limited. Finally, the experimental trends were compared with CHEMKIN (single zone, 0-D model) predictions using multiple kinetic mechanism that were readily available through literature. Due to the simplicity of the model and inadequate information on the fuel injection process, the experimental data was not modeled well with the mechanisms tested. Some of the shortcomings of the 0-D model were probably due to the model ignoring temperature and composition spatial inhomogeneities and evaporative cooling from fuel vaporization.Though the results from the NVO injection and boosted NVO-HCCI studies are enlightening, the fundamentals of the autoignition behavior of gasoline, alcohols, and their mixtures are not entirely understood despite the interest in high octane fuels in compression engines from a point of view of better thermal efficiency. The third study focused on higher octane blends consisting of binary and ternary mixtures of n-heptane and/or iso-octane, and a fuel of interest. These fuels of interest were toluene, ethanol, and iso-butanol. In this study, the autoignition of such blends is studied under lean conditions ([phi] = 0.25) with varying intake pressure (atmospheric to 3 bar, abs) and at a constant intake temperature of 155 °C. The blends consisted of varying percentages of fuels of interest and their research octane number (RON) approximately estimated at 100 and 80. For comparison, neat iso-octane was selected as RON 100 fuel and PRF 80 blend was selected as RON 80 fuel. It was observed that the blends with a higher percentage of n-heptane showed a stronger tendency to autoignite at lower intake pressures. However, as the intake pressure was increased, the non-reactive components, in this case, the higher octane blend components (toluene, ethanol, and iso-butanol), reduced this tendency subsequently delaying the critical compression ratio (CCR) of the blends. The heat release analysis revealed that the higher octane components in the blends reduced the low temperature reactivity of n-heptane and iso-octane. GC-MS and GC-FID analysis of the partially compressed fuel also indicated that the higher octane components did affect the conversion of the more reactive components, n-heptane and iso-octane, into their partially oxidized branched hydrocarbons in the binary/ternary blends, and reduced the overall reactivity which resulted in a delayed CCR at higher intake pressures.
div="" This book covers different aspects related to utilization of alcohol fuels in internal combustion (IC) engines with a focus on combustion, performance and emission investigations. The focal point of this book is to present engine combustion, performance and emission characteristics of IC engines fueled by alcohol blended fuels such as methanol, ethanol and butanol. The contents also highlight the importance of alcohol fuel for reducing emission levels. Possibility of alcohol fuels for marine applications has also been discussed. This book is a useful guide for researchers, academics and scientists. ^
This book covers the various advanced reciprocating combustion engine technologies that utilize natural gas and alternative fuels for transportation and power generation applications. It is divided into three major sections consisting of both fundamental and applied technologies to identify (but not limited to) clean, high-efficiency opportunities with natural gas fueling that have been developed through experimental protocols, numerical and high-performance computational simulations, and zero-dimensional, multizone combustion simulations. Particular emphasis is placed on statutes to monitor fine particulate emissions from tailpipe of engines operating on natural gas and alternative fuels.