Download Free Design Criteria For Strength And Serviceability Of Inverted T Straddle Bent Caps Book in PDF and EPUB Free Download. You can read online Design Criteria For Strength And Serviceability Of Inverted T Straddle Bent Caps and write the review.

Several recently built inverted-T bent caps in Texas have shown significant inclined cracking triggering concern about current design procedures for such structures. The repair of such structures is very costly and often requires lane closures. For these reasons TxDOT funded Project 0-6416 aimed at obtaining a better understanding of the structural behavior of inverted-T bent caps and developing new design criteria to minimize such cracking in the future. Several tasks of the aforementioned project are addressed in this dissertation with particular focus on developing design criteria for strength and serviceability of inverted-T bent caps. Literature review revealed a scarcity of experimental investigation of inverted-T specimens. As part of this dissertation, an inverted-T database was assembled with experimental results from the literature and the current project. An extensive experimental program was completed to accomplish the objectives of the project with thirty one full-scale tests conducted on inverted-T beams. Experimental parameters varied in the study were: ledge length, ledge depth, web reinforcement, number of point loads, web depth, and shear span-to-depth ratio. The dissertation focuses on the effects of ledge length, ledge depth, number of point loads, and developing design criteria for strength and serviceability of inverted-T beams. Most inverted-T bent caps in Texas are designed using the traditional empirical design procedures outlined in the TxDOT bridge design manual LRFD (2011 current version) that follows closely the AASHTO LRFD bridge design specifications (2012 current version). Given the observed cracking in inverted-T bent caps, the accuracy and conservatism of the traditional design methods were evaluated based on experimental results. The accuracy and conservatism of STM design provisions recently developed in a TxDOT study (TxDOT Project 0-5253, Strength and Serviceability Design of Reinforced Concrete Deep Beams) were also evaluated.
"Prepared by members of ACI Subcommittee 445-1, Strut and Tie Models, for sessions at the Fall Convention in Phoenix, October 27 to November 1, 2002, and sponsored by Joint ACI-ASCE Committee 445, Shear and Torsion and ACI Committee 318-E, Shear and Torsion."
The "Red Book" presents a background to conventional foundation analysis and design. The text is not intended to replace the much more comprehensive 'standard' textbooks, but rather to support and augment these in a few important areas, supplying methods applicable to practical cases handled daily by practising engineers and providing the basic soil mechanics background to those methods. It concentrates on the static design for stationary foundation conditions. Although the topic is far from exhaustively treated, it does intend to present most of the basic material needed for a practising engineer involved in routine geotechnical design, as well as provide the tools for an engineering student to approach and solve common geotechnical design problems.
Significant diagonal cracking in reinforced concrete inverted-T straddle bent caps has been reported throughout the State of Texas. Many of the distressed structures were recently constructed and all have been in service for less than two decades. The unique nature of the problem prompted a more detailed look into the design and behavior of such structural components. Strut-and-tie modeling is currently recommended for design of deep (rectangular) beams, but its application to more complex structures has not been fully explored. Due to concerns with current design provisions the application of strut-and-tie modeling to inverted-T beams was investigated along with serviceability-related considerations in this dissertation. An experimental study was conducted in which thirty-three reinforced concrete inverted-T beam tests were conducted. The effects of the following variables were evaluated: ledge depth and length, quantity of web reinforcement, number of point loads, member depth, and shear span-to-depth ratio. A strut-and-tie design method proposed by Birrcher et. al (2009), initially calibrated for compression-chord loaded deep beams, was investigated. It was concluded that the strut-and-tie method was a simple and accurate design method, and it was recommended for use in inverted-T beam design. A vi recommendation was also made for the amount of minimum web reinforcement needed for strength and serviceability considerations. A simple service-load check was proposed for the purpose of limiting diagonal cracking under service loads. Finally, a chart was created to aid in the evaluation of distressed, diagonally-cracked inverted-T bent caps in the field.
Significant diagonal cracking in reinforced concrete inverted-T (IT) straddle bent caps has been reported throughout the State of Texas. Many of the distressed structures were recently constructed and have generally been in service for less than two decades. The unique nature of the problem prompted a closer look into the design and behavior of such structural components. A preliminary investigation highlighted outdated design requirements and a scarcity of experimental investigations pertaining to inverted-T bent caps. This research project (TxDOT Project 0-6416, Shear Cracking in Inverted-T Straddle Bents) aims to improve current understanding of the behavior of inverted-T caps, while providing updated design provisions. In order to develop strength and serviceability guidelines for inverted-T beams, an extensive experimental program was developed. This series of large scale tests was used to evaluate the strength and serviceability of IT deep beams in relation to the following parameters -- shear span-to-depth (a/d) ratio, web reinforcement ratio, ledge height, ledge length, number of point loads, and member depth. This report focuses mainly on results from a first series of tests conducted within this experimental program.
High strength fibre composites (FRPs) have been used with civil structures since the 1980s, mostly in the repair, strengthening and retrofitting of concrete structures. This has attracted considerable research, and the industry has expanded exponentially in the last decade. Design guidelines have been developed by professional organizations in a nu
Provides a practical design guide to the structural use of aluminium. The first chapters outline basic aluminium technology and the advantages of using aluminium in many structural applications. The major part of the book deals with structural design and presents very clear guidance for designers, with numerous diagrams, charts and examples.
Die zweite Auflage dieses Klassikers - jetzt als Paperback - bietet Profis auf diesem Gebiet eine aktuelle und kompetente Präsentation der Technologie der Vorbelastung von Stahlbeton. Grundlegende Techniken, Materialien und Systeme werden behandelt und vielfältige Anwendungen - Gebäude, Brücken, Bohrplattformen, Straßen, Rollbahnen, Rohrleitungen - erläutert.
Surveys the leading methods for connecting structural steel components, covering state-of-the-art techniques and materials, and includes new information on welding and connections. Hundreds of detailed examples, photographs, and illustrations are found throughout this handbook. --from publisher description.